Acer Veriton N4670g vs. Dell OptiPlex 3050 MT
Comparison and Differences
Differences between Acer Veriton N4670g and Dell OptiPlex 3050 MT
If you are looking for a more modern desktop, then you should go with the Acer Veriton N4670g which was released in 2020. The Dell OptiPlex 3050 MT is older and entered production in 2017.
If you are looking for the smaller form factor the Acer Veriton N4670g is the right one for you. It is smaller than the Dell OptiPlex 3050 MT and will fit more easily under your desk.
Processor
Usually the newer the generation of the CPU, the better the performance and efficiency is. If your budget allows it, you should go with the Acer Veriton N4670g as it is running a newer generation CPU. This is not to say that Dell OptiPlex 3050 MT is bad - it can still run some powerful CPUs, albeit being an older generation.
Memory
Both models have have equal amount of ram slots (2 RAM). Usually two RAM slots are more than enough for most cases. However, the count should be taken into account when planning how much and what combination of RAM you are going to need for your system.
The Acer Veriton N4670g is using the faster 2933 MT/s RAM. The Dell OptiPlex 3050 MT is slower by supporting RAM speeds of up to 2400 MT/s. In addition, you will be able to install the same amount of RAM in both models, and most probably 32 GB of RAM will be enough for most people. However, if you will be needing more RAM, make sure to check other desktop models too.
Ports
In total the Dell OptiPlex 3050 MT has 8 USB ports. The Acer Veriton N4670g is inferior in this regard and packs 7 USB ports. In any case, if you miss USB ports, you can always purchase a USB hub. What is nice about the Acer Veriton N4670g, is that it has 2 USB 3.1 port(s) which allows transfer of up to 10Gb/s. Unfortunately, the Dell OptiPlex 3050 MT has no such port, thus restricting your transfer speeds significantly. For people who want to use external drives on regular basis, this might be an issue.
The DisplayPort is usually the more popular video port used with desktops and laptops, while the HDMI is used predominantly in consumer electronics. That's why, it is good to see that both of the models come with a DisplayPort.
In case your monitor supports HDMI only, you will be happy to hear that both models come with an HDMI port.
SATA ports are placed on the system board and it is where you connect your HDD, SSD and Optical Disk Drives. More SATA slots will allow you to have more drives running at the same time. In this regard the Dell OptiPlex 3050 MT is better equipped as it comes with 3 SATA slot(s), while the Acer Veriton N4670g has 1 slot(s).
An M.2 SSD can be several times faster than a SATA one. Thus, we are happy to see that both models support the M.2 interface. However, the Acer Veriton N4670g has 1 M.2 slots while the Dell OptiPlex 3050 MT comes with just 1.
Make sure that the available M.2 slot supports the PCIe (also called NVMe) interface. This is important as there are M.2 slots which support only the inferior SATA III interface. For comparison, the SATA III interface has max speeds of 6Gb/s, while the PCIe 3.0 x4 will support speeds up to 32Gb/s!
Power Supply
Having a Power Supply Unit with high power rating is important, if you are going to use components which require extra power. The Acer Veriton N4670g comes with a decent 90 Watt PSU, but the Dell OptiPlex 3050 MT has a more powerful one rated at 240 Watts. Choosing either one depends on your specific requirements and use case. Also don't forget that some models might have more than one PSU option - try to always get the most powerful one, especially if you plan to upgrade to a powerful GPU.
Motherboard
