Acer Veriton X4670g vs. Dell OptiPlex 5060 MT
Comparison and Differences
Differences between Acer Veriton X4670g and Dell OptiPlex 5060 MT
If you are looking for a more modern desktop, then you should go with the Acer Veriton X4670g which was released in 2020. The Dell OptiPlex 5060 MT is older and entered production in 2018.
If you are looking for the smaller form factor the Acer Veriton X4670g is the right one for you. It is smaller than the Dell OptiPlex 5060 MT and will fit more easily under your desk.
Processor
Usually the newer the generation of the CPU, the better the performance and efficiency is. If your budget allows it, you should go with the Acer Veriton X4670g as it is running a newer generation CPU. This is not to say that Dell OptiPlex 5060 MT is bad - it can still run some powerful CPUs, albeit being an older generation.
Memory
The Dell OptiPlex 5060 MT has 4 RAM slots while the Acer Veriton X4670g has only 2 slot(s). This is not something to worry about. Just make sure you take it into consideration when planning how much RAM you are going to use.
The Acer Veriton X4670g is using the faster 2933 MT/s RAM. The Dell OptiPlex 5060 MT is slower by supporting RAM speeds of up to 2666 MT/s. In addition, you will be able to install the same amount of RAM in both models, and most probably 64 GB of RAM will be enough for most people. However, if you will be needing more RAM, make sure to check other desktop models too.
Ports
In total the Dell OptiPlex 5060 MT has 10 USB ports. The Acer Veriton X4670g is inferior in this regard and packs 9 USB ports. In any case, if you miss USB ports, you can always purchase a USB hub. It's great that both of the models have USB 3.1 ports which will allow you to exchange data with your peripherals at up to 10Gb/s. But if you need maximum connectivity, go with the Acer Veriton X4670g as it has 5 USB3.1 ports (the Dell OptiPlex 5060 MT has 1).
The DisplayPort is usually the more popular video port used with desktops and laptops, while the HDMI is used predominantly in consumer electronics. That's why, it is good to see that both of the models come with a DisplayPort.
None of the models has an HDMI port. If your monitor supports only the HDMI interface, you will need to buy an adapter. Such adapters are cheap so nothing to worry about.
SATA ports are placed on the system board and it is where you connect your HDD, SSD and Optical Disk Drives. More SATA slots will allow you to have more drives running at the same time. In this regard the Dell OptiPlex 5060 MT is better equipped as it comes with 4 SATA slot(s), while the Acer Veriton X4670g has 3 slot(s).
When your goal is to have the fastest SSD transfer speeds, an M.2 interface is crucial. Thus, it is good that both models have M.2 SSD slots. Today M.2 SSDs are not much more expensive than the average SATA drives, so it really does not make sense to invest in SATA drives anymore.
Make sure that the available M.2 slot supports the PCIe (also called NVMe) interface. This is important as there are M.2 slots which support only the inferior SATA III interface. For comparison, the SATA III interface has max speeds of 6Gb/s, while the PCIe 3.0 x4 will support speeds up to 32Gb/s!
Power Supply
Having a Power Supply Unit with high power rating is important, if you are going to use components which require extra power. The Dell OptiPlex 5060 MT comes with a decent 260 Watt PSU, but the Acer Veriton X4670g has a more powerful one rated at 300 Watts. Choosing either one depends on your specific requirements and use case. Also don't forget that some models might have more than one PSU option - try to always get the most powerful one, especially if you plan to upgrade to a powerful GPU.
Motherboard
