Alienware Aurora R11 vs. Dell OptiPlex 5070 SFF
Comparison and Differences
Differences between Alienware Aurora R11 and Dell OptiPlex 5070 SFF
If you are looking for a more modern desktop, then you should go with the Alienware Aurora R11 which was released in 2020. The Dell OptiPlex 5070 SFF is older and entered production in 2019.
If you are looking for the smaller form factor the Dell OptiPlex 5070 SFF is the right one for you. It is smaller than the Alienware Aurora R11 and will fit more easily under your desk.
Processor
Usually the newer the generation of the CPU, the better the performance and efficiency is. If your budget allows it, you should go with the Alienware Aurora R11 as it is running a newer generation CPU. This is not to say that Dell OptiPlex 5070 SFF is bad - it can still run some powerful CPUs, albeit being an older generation.
Memory
Both models have have equal amount of ram slots (4 RAM). Usually two RAM slots are more than enough for most cases. However, the count should be taken into account when planning how much and what combination of RAM you are going to need for your system.
The Alienware Aurora R11 is using the faster 3400 MT/s RAM. The Dell OptiPlex 5070 SFF is slower by supporting RAM speeds of up to 2666 MT/s. Additionally, if you will be needing a lot of RAM, better go for the Alienware Aurora R11 as it has the ability to run 128 GB of RAM. The Dell OptiPlex 5070 SFF can do a bit less at max 64 GB. Most of the times, this should be sufficient for the majority of users.
Ports
In total the Alienware Aurora R11 has 15 USB ports. The Dell OptiPlex 5070 SFF is inferior in this regard and packs 10 USB ports. In any case, if you miss USB ports, you can always purchase a USB hub. It's great that both of the models have USB 3.1 ports which will allow you to exchange data with your peripherals at up to 10Gb/s. But if you need maximum connectivity, go with the Alienware Aurora R11 as it has 3 USB3.1 ports (the Dell OptiPlex 5070 SFF has 1).
Unfortunately, only the Dell OptiPlex 5070 SFF has a DisplayPort. The Alienware Aurora R11 does not have one? Don't worry though, nowadays video adapters are cheap and you can get almost any combination of conversion types.
None of the models has an HDMI port. If your monitor supports only the HDMI interface, you will need to buy an adapter. Such adapters are cheap so nothing to worry about.
SATA ports are placed on the system board and it is where you connect your HDD, SSD and Optical Disk Drives. More SATA slots will allow you to have more drives running at the same time. In this regard the Alienware Aurora R11 is better equipped as it comes with 4 SATA slot(s), while the Dell OptiPlex 5070 SFF has 3 slot(s).
When your goal is to have the fastest SSD transfer speeds, an M.2 interface is crucial. Thus, it is good that both models have M.2 SSD slots. Today M.2 SSDs are not much more expensive than the average SATA drives, so it really does not make sense to invest in SATA drives anymore.
Make sure that the available M.2 slot supports the PCIe (also called NVMe) interface. This is important as there are M.2 slots which support only the inferior SATA III interface. For comparison, the SATA III interface has max speeds of 6Gb/s, while the PCIe 3.0 x4 will support speeds up to 32Gb/s!
Power Supply
Having a Power Supply Unit with high power rating is important, if you are going to use components which require extra power. The Dell OptiPlex 5070 SFF comes with a decent 200 Watt PSU, but the Alienware Aurora R11 has a more powerful one rated at 1000 Watts. Choosing either one depends on your specific requirements and use case. Also don't forget that some models might have more than one PSU option - try to always get the most powerful one, especially if you plan to upgrade to a powerful GPU.