Alienware Aurora R11 vs. HP ProDesk 600 G4 Microtower

Differences between Alienware Aurora R11 and HP ProDesk 600 G4 Microtower

If you are looking for a more modern desktop, then you should go with the Alienware Aurora R11 which was released in 2020. The HP ProDesk 600 G4 Microtower is older and entered production in 2018.

If you are looking for the smaller form factor the Alienware Aurora R11 is the right one for you. It is smaller than the HP ProDesk 600 G4 Microtower and will fit more easily under your desk.

Processor

Usually the newer the generation of the CPU, the better the performance and efficiency is. If your budget allows it, you should go with the Alienware Aurora R11 as it is running a newer generation CPU. This is not to say that HP ProDesk 600 G4 Microtower is bad - it can still run some powerful CPUs, albeit being an older generation.

Memory

Both models have have equal amount of ram slots (4 RAM). Usually two RAM slots are more than enough for most cases. However, the count should be taken into account when planning how much and what combination of RAM you are going to need for your system.

The Alienware Aurora R11 is using the faster 3400 MT/s RAM. The HP ProDesk 600 G4 Microtower is slower by supporting RAM speeds of up to 2666 MT/s. Additionally, if you will be needing a lot of RAM, better go for the Alienware Aurora R11 as it has the ability to run 128 GB of RAM. The HP ProDesk 600 G4 Microtower can do a bit less at max 64 GB. Most of the times, this should be sufficient for the majority of users.

Ports

In total the Alienware Aurora R11 has 15 USB ports. The HP ProDesk 600 G4 Microtower is inferior in this regard and packs 11 USB ports. In any case, if you miss USB ports, you can always purchase a USB hub. It's great that both of the models have USB 3.1 ports which will allow you to exchange data with your peripherals at up to 10Gb/s. But if you need maximum connectivity, go with the HP ProDesk 600 G4 Microtower as it has 5 USB3.1 ports (the Alienware Aurora R11 has 3).

Unfortunately, only the HP ProDesk 600 G4 Microtower has a DisplayPort. The Alienware Aurora R11 does not have one? Don't worry though, nowadays video adapters are cheap and you can get almost any combination of conversion types.

None of the models has an HDMI port. If your monitor supports only the HDMI interface, you will need to buy an adapter. Such adapters are cheap so nothing to worry about.

SATA slots are located on the motherboard and it is where SSD, HDD and Optical Disk Drives are connected. Each of the two models being compared have 4 SATA slot(s). Keep in mind that having too few SATA slots might limit your options for connecting additional memory drives.

When your goal is to have the fastest SSD transfer speeds, an M.2 interface is crucial. Thus, it is good that both models have M.2 SSD slots. Today M.2 SSDs are not much more expensive than the average SATA drives, so it really does not make sense to invest in SATA drives anymore.

Make sure that the available M.2 slot supports the PCIe (also called NVMe) interface. This is important as there are M.2 slots which support only the inferior SATA III interface. For comparison, the SATA III interface has max speeds of 6Gb/s, while the PCIe 3.0 x4 will support speeds up to 32Gb/s!

Power Supply

Having a Power Supply Unit with high power rating is important, if you are going to use components which require extra power. The HP ProDesk 600 G4 Microtower comes with a decent 400 Watt PSU, but the Alienware Aurora R11 has a more powerful one rated at 1000 Watts. Choosing either one depends on your specific requirements and use case. Also don't forget that some models might have more than one PSU option - try to always get the most powerful one, especially if you plan to upgrade to a powerful GPU.

Motherboard