Dell OptiPlex 3040M vs. Fujitsu Esprimo P520
Comparison and Differences
Differences between Dell OptiPlex 3040M and Fujitsu Esprimo P520
If you are looking for a more modern desktop, then you should go with the Dell OptiPlex 3040M which was released in 2015. The Fujitsu Esprimo P520 is older and entered production in 2014.
If you are looking for the smaller form factor the Dell OptiPlex 3040M is the right one for you. It is smaller than the Fujitsu Esprimo P520 and will fit more easily under your desk.
Processor
Usually the newer the generation of the CPU, the better the performance and efficiency is. If your budget allows it, you should go with the Dell OptiPlex 3040M as it is running a newer generation CPU. This is not to say that Fujitsu Esprimo P520 is bad - it can still run some powerful CPUs, albeit being an older generation.
Memory
The Fujitsu Esprimo P520 has 4 RAM slots while the Dell OptiPlex 3040M has only 2 slot(s). This is not something to worry about. Just make sure you take it into consideration when planning how much RAM you are going to use.
None of the desktops has an advantage when it comes to the speed of the RAM being used. Both models support RAM speeds of up to 1600. Additionally, if you will be needing a lot of RAM, better go for the Fujitsu Esprimo P520 as it has the ability to run 32 GB of RAM. The Dell OptiPlex 3040M can do a bit less at max 16 GB. Most of the times, this should be sufficient for the majority of users.
Ports
In total the Fujitsu Esprimo P520 has 8 USB ports. The Dell OptiPlex 3040M is inferior in this regard and packs 6 USB ports. In any case, if you miss USB ports, you can always purchase a USB hub. None of the desktop models has a USB 3.1 port (10Gb/s), so if you need a fast connection to your peripherals, like external Solid State Drive, you will need to look elsewhere.
The DisplayPort is usually the more popular video port used with desktops and laptops, while the HDMI is used predominantly in consumer electronics. That's why, it is good to see that both of the models come with a DisplayPort.
The Dell OptiPlex 3040M comes with an HDMI port, while the Fujitsu Esprimo P520 does not support the interface. Of course missing HDMI port is something that can be easily fixed with a good adapter (e.g. DisplayPort to HDMI).
SATA ports are placed on the system board and it is where you connect your HDD, SSD and Optical Disk Drives. More SATA slots will allow you to have more drives running at the same time. In this regard the Fujitsu Esprimo P520 is better equipped as it comes with 4 SATA slot(s), while the Dell OptiPlex 3040M has 1 slot(s).
M.2 SSD interface allows you to transfer data with higher speeds compared to the old SATA interface. Unfortunately, neither the Dell OptiPlex 3040M, nor the Fujitsu Esprimo P520 has one. However, you can still use a SATA SSD drive which should give you satisfactory performance.
Make sure that the available M.2 slot supports the PCIe (also called NVMe) interface. This is important as there are M.2 slots which support only the inferior SATA III interface. For comparison, the SATA III interface has max speeds of 6Gb/s, while the PCIe 3.0 x4 will support speeds up to 32Gb/s!
Power Supply
Having a Power Supply Unit with high power rating is important, if you are going to use components which require extra power. The Dell OptiPlex 3040M comes with a decent 65 Watt PSU, but the Fujitsu Esprimo P520 has a more powerful one rated at 280 Watts. Choosing either one depends on your specific requirements and use case. Also don't forget that some models might have more than one PSU option - try to always get the most powerful one, especially if you plan to upgrade to a powerful GPU.
Motherboard
