Acer Veriton N4630g vs. Dell OptiPlex 3060 MT
Comparison and Differences
Differences between Acer Veriton N4630g and Dell OptiPlex 3060 MT
If you are looking for a more modern desktop, then you should go with the Dell OptiPlex 3060 MT which was released in 2018. The Acer Veriton N4630g is older and entered production in 2014.
If you are looking for the smaller form factor the Acer Veriton N4630g is the right one for you. It is smaller than the Dell OptiPlex 3060 MT and will fit more easily under your desk.
Processor
Usually the newer the generation of the CPU, the better the performance and efficiency is. If your budget allows it, you should go with the Dell OptiPlex 3060 MT as it is running a newer generation CPU. This is not to say that Acer Veriton N4630g is bad - it can still run some powerful CPUs, albeit being an older generation.
Memory
Both models have have equal amount of ram slots (2 RAM). Usually two RAM slots are more than enough for most cases. However, the count should be taken into account when planning how much and what combination of RAM you are going to need for your system.
The Dell OptiPlex 3060 MT is using the faster 2666 MT/s RAM. The Acer Veriton N4630g is slower by supporting RAM speeds of up to 1600 MT/s. Additionally, if you will be needing a lot of RAM, better go for the Dell OptiPlex 3060 MT as it has the ability to run 32 GB of RAM. The Acer Veriton N4630g can do a bit less at max 16 GB. Most of the times, this should be sufficient for the majority of users.
Ports
In total the Dell OptiPlex 3060 MT has 8 USB ports. The Acer Veriton N4630g is inferior in this regard and packs 5 USB ports. In any case, if you miss USB ports, you can always purchase a USB hub. None of the desktop models has a USB 3.1 port (10Gb/s), so if you need a fast connection to your peripherals, like external Solid State Drive, you will need to look elsewhere.
The DisplayPort is usually the more popular video port used with desktops and laptops, while the HDMI is used predominantly in consumer electronics. That's why, it is good to see that both of the models come with a DisplayPort.
The Dell OptiPlex 3060 MT comes with an HDMI port, while the Acer Veriton N4630g does not support the interface. Of course missing HDMI port is something that can be easily fixed with a good adapter (e.g. DisplayPort to HDMI).
SATA ports are placed on the system board and it is where you connect your HDD, SSD and Optical Disk Drives. More SATA slots will allow you to have more drives running at the same time. In this regard the Dell OptiPlex 3060 MT is better equipped as it comes with 3 SATA slot(s), while the Acer Veriton N4630g has 1 slot(s).
If you want the fastest transfer speeds for your SSD, an M.2 interface is crucial. Thus, if the M.2 SSD slot is a mandatory requirement for you, go with the Dell OptiPlex 3060 MT. Sadly, the Acer Veriton N4630g has no such slot, and you will be forced to use the SATA interface instead.
Make sure that the available M.2 slot supports the PCIe (also called NVMe) interface. This is important as there are M.2 slots which support only the inferior SATA III interface. For comparison, the SATA III interface has max speeds of 6Gb/s, while the PCIe 3.0 x4 will support speeds up to 32Gb/s!
Power Supply
Having a Power Supply Unit with high power rating is important, if you are going to use components which require extra power. The Acer Veriton N4630g comes with a decent 90 Watt PSU, but the Dell OptiPlex 3060 MT has a more powerful one rated at 260 Watts. Choosing either one depends on your specific requirements and use case. Also don't forget that some models might have more than one PSU option - try to always get the most powerful one, especially if you plan to upgrade to a powerful GPU.
Motherboard
