Acer Veriton X4640g vs. Dell OptiPlex 3090 M
Comparison and Differences
Differences between Acer Veriton X4640g and Dell OptiPlex 3090 M
If you are looking for a more modern desktop, then you should go with the Dell OptiPlex 3090 M which was released in 2021. The Acer Veriton X4640g is older and entered production in 2015.
If you are looking for the smaller form factor the Dell OptiPlex 3090 M is the right one for you. It is smaller than the Acer Veriton X4640g and will fit more easily under your desk.
Processor
Usually the newer the generation of the CPU, the better the performance and efficiency is. If your budget allows it, you should go with the Dell OptiPlex 3090 M as it is running a newer generation CPU. This is not to say that Acer Veriton X4640g is bad - it can still run some powerful CPUs, albeit being an older generation.
Memory
The Acer Veriton X4640g has 4 RAM slots while the Dell OptiPlex 3090 M has only 2 slot(s). This is not something to worry about. Just make sure you take it into consideration when planning how much RAM you are going to use.
The Dell OptiPlex 3090 M is using the faster 2933 MT/s RAM. The Acer Veriton X4640g is slower by supporting RAM speeds of up to 2133 MT/s. Additionally, if you will be needing a lot of RAM, better go for the Dell OptiPlex 3090 M as it has the ability to run 64 GB of RAM. The Acer Veriton X4640g can do a bit less at max 32 GB. Most of the times, this should be sufficient for the majority of users.
Ports
In total the Acer Veriton X4640g has 10 USB ports. The Dell OptiPlex 3090 M is inferior in this regard and packs 5 USB ports. In any case, if you miss USB ports, you can always purchase a USB hub. None of the desktop models has a USB 3.1 port (10Gb/s), so if you need a fast connection to your peripherals, like external Solid State Drive, you will need to look elsewhere.
DisplayPort is crucial for any desktop machine. It is good to see that both models are featuring DisplayPorts. However, the Acer Veriton X4640g comes with 2 ports, while the Dell OptiPlex 3090 M has only 1. If you are planning to use multiple monitors, the Acer Veriton X4640g is the better choice.
None of the models has an HDMI port. If your monitor supports only the HDMI interface, you will need to buy an adapter. Such adapters are cheap so nothing to worry about.
SATA ports are placed on the system board and it is where you connect your HDD, SSD and Optical Disk Drives. More SATA slots will allow you to have more drives running at the same time. In this regard the Acer Veriton X4640g is better equipped as it comes with 3 SATA slot(s), while the Dell OptiPlex 3090 M has 1 slot(s).
If you want the fastest transfer speeds for your SSD, an M.2 interface is crucial. Thus, if the M.2 SSD slot is a mandatory requirement for you, go with the Dell OptiPlex 3090 M. Sadly, the Acer Veriton X4640g has no such slot, and you will be forced to use the SATA interface instead.
Make sure that the available M.2 slot supports the PCIe (also called NVMe) interface. This is important as there are M.2 slots which support only the inferior SATA III interface. For comparison, the SATA III interface has max speeds of 6Gb/s, while the PCIe 3.0 x4 will support speeds up to 32Gb/s!
Power Supply
Having a Power Supply Unit with high power rating is important, if you are going to use components which require extra power. The Dell OptiPlex 3090 M comes with a decent 65 Watt PSU, but the Acer Veriton X4640g has a more powerful one rated at 220 Watts. Choosing either one depends on your specific requirements and use case. Also don't forget that some models might have more than one PSU option - try to always get the most powerful one, especially if you plan to upgrade to a powerful GPU.
Motherboard
