Dell G5 5090 vs. Dell OptiPlex 3090 M
Comparison and Differences
Differences between Dell G5 5090 and Dell OptiPlex 3090 M
If you are looking for a more modern desktop, then you should go with the Dell OptiPlex 3090 M which was released in 2021. The Dell G5 5090 is older and entered production in 2019.
If you are looking for the smaller form factor the Dell OptiPlex 3090 M is the right one for you. It is smaller than the Dell G5 5090 and will fit more easily under your desk.
Processor
Usually the newer the generation of the CPU, the better the performance and efficiency is. If your budget allows it, you should go with the Dell OptiPlex 3090 M as it is running a newer generation CPU. This is not to say that Dell G5 5090 is bad - it can still run some powerful CPUs, albeit being an older generation.
Memory
The Dell G5 5090 has 4 RAM slots while the Dell OptiPlex 3090 M has only 2 slot(s). This is not something to worry about. Just make sure you take it into consideration when planning how much RAM you are going to use.
The Dell OptiPlex 3090 M is using the faster 2933 MT/s RAM. The Dell G5 5090 is slower by supporting RAM speeds of up to 2666 MT/s. In addition, you will be able to install the same amount of RAM in both models, and most probably 64 GB of RAM will be enough for most people. However, if you will be needing more RAM, make sure to check other desktop models too.
Ports
In total the Dell G5 5090 has 9 USB ports. The Dell OptiPlex 3090 M is inferior in this regard and packs 5 USB ports. In any case, if you miss USB ports, you can always purchase a USB hub. What is nice about the Dell G5 5090, is that it has 2 USB 3.1 port(s) which allows transfer of up to 10Gb/s. Unfortunately, the Dell OptiPlex 3090 M has no such port, thus restricting your transfer speeds significantly. For people who want to use external drives on regular basis, this might be an issue.
Unfortunately, only the Dell OptiPlex 3090 M has a DisplayPort. The Dell G5 5090 does not have one? Don't worry though, nowadays video adapters are cheap and you can get almost any combination of conversion types.
None of the models has an HDMI port. If your monitor supports only the HDMI interface, you will need to buy an adapter. Such adapters are cheap so nothing to worry about.
SATA ports are placed on the system board and it is where you connect your HDD, SSD and Optical Disk Drives. More SATA slots will allow you to have more drives running at the same time. In this regard the Dell G5 5090 is better equipped as it comes with 3 SATA slot(s), while the Dell OptiPlex 3090 M has 1 slot(s).
When your goal is to have the fastest SSD transfer speeds, an M.2 interface is crucial. Thus, it is good that both models have M.2 SSD slots. Today M.2 SSDs are not much more expensive than the average SATA drives, so it really does not make sense to invest in SATA drives anymore.
Make sure that the available M.2 slot supports the PCIe (also called NVMe) interface. This is important as there are M.2 slots which support only the inferior SATA III interface. For comparison, the SATA III interface has max speeds of 6Gb/s, while the PCIe 3.0 x4 will support speeds up to 32Gb/s!
Power Supply
Having a Power Supply Unit with high power rating is important, if you are going to use components which require extra power. The Dell OptiPlex 3090 M comes with a decent 65 Watt PSU, but the Dell G5 5090 has a more powerful one rated at 460 Watts. Choosing either one depends on your specific requirements and use case. Also don't forget that some models might have more than one PSU option - try to always get the most powerful one, especially if you plan to upgrade to a powerful GPU.
Motherboard
