Dell OptiPlex 3090 M vs. Fujitsu Esprimo D738
Comparison and Differences
Differences between Dell OptiPlex 3090 M and Fujitsu Esprimo D738
If you are looking for a more modern desktop, then you should go with the Dell OptiPlex 3090 M which was released in 2021. The Fujitsu Esprimo D738 is older and entered production in 2018.
If you are looking for the smaller form factor the Dell OptiPlex 3090 M is the right one for you. It is smaller than the Fujitsu Esprimo D738 and will fit more easily under your desk.
Processor
Usually the newer the generation of the CPU, the better the performance and efficiency is. If your budget allows it, you should go with the Dell OptiPlex 3090 M as it is running a newer generation CPU. This is not to say that Fujitsu Esprimo D738 is bad - it can still run some powerful CPUs, albeit being an older generation.
Memory
The Fujitsu Esprimo D738 has 4 RAM slots while the Dell OptiPlex 3090 M has only 2 slot(s). This is not something to worry about. Just make sure you take it into consideration when planning how much RAM you are going to use.
The Dell OptiPlex 3090 M is using the faster 2933 MT/s RAM. The Fujitsu Esprimo D738 is slower by supporting RAM speeds of up to 2666 MT/s. In addition, you will be able to install the same amount of RAM in both models, and most probably 64 GB of RAM will be enough for most people. However, if you will be needing more RAM, make sure to check other desktop models too.
Ports
In total the Fujitsu Esprimo D738 has 13 USB ports. The Dell OptiPlex 3090 M is inferior in this regard and packs 5 USB ports. In any case, if you miss USB ports, you can always purchase a USB hub. What is nice about the Fujitsu Esprimo D738, is that it has 3 USB 3.1 port(s) which allows transfer of up to 10Gb/s. Unfortunately, the Dell OptiPlex 3090 M has no such port, thus restricting your transfer speeds significantly. For people who want to use external drives on regular basis, this might be an issue.
DisplayPort is crucial for any desktop machine. It is good to see that both models are featuring DisplayPorts. However, the Fujitsu Esprimo D738 comes with 2 ports, while the Dell OptiPlex 3090 M has only 1. If you are planning to use multiple monitors, the Fujitsu Esprimo D738 is the better choice.
None of the models has an HDMI port. If your monitor supports only the HDMI interface, you will need to buy an adapter. Such adapters are cheap so nothing to worry about.
SATA ports are placed on the system board and it is where you connect your HDD, SSD and Optical Disk Drives. More SATA slots will allow you to have more drives running at the same time. In this regard the Fujitsu Esprimo D738 is better equipped as it comes with 5 SATA slot(s), while the Dell OptiPlex 3090 M has 1 slot(s).
When your goal is to have the fastest SSD transfer speeds, an M.2 interface is crucial. Thus, it is good that both models have M.2 SSD slots. Today M.2 SSDs are not much more expensive than the average SATA drives, so it really does not make sense to invest in SATA drives anymore.
Make sure that the available M.2 slot supports the PCIe (also called NVMe) interface. This is important as there are M.2 slots which support only the inferior SATA III interface. For comparison, the SATA III interface has max speeds of 6Gb/s, while the PCIe 3.0 x4 will support speeds up to 32Gb/s!
Power Supply
Having a Power Supply Unit with high power rating is important, if you are going to use components which require extra power. The Dell OptiPlex 3090 M comes with a decent 65 Watt PSU, but the Fujitsu Esprimo D738 has a more powerful one rated at 280 Watts. Choosing either one depends on your specific requirements and use case. Also don't forget that some models might have more than one PSU option - try to always get the most powerful one, especially if you plan to upgrade to a powerful GPU.
Motherboard
