Dell OptiPlex 5000 M vs. HP ProDesk 600 G3 Microtower
Comparison and Differences
Differences between Dell OptiPlex 5000 M and HP ProDesk 600 G3 Microtower
If you are looking for a more modern desktop, then you should go with the Dell OptiPlex 5000 M which was released in 2022. The HP ProDesk 600 G3 Microtower is older and entered production in 2017.
If you are looking for the smaller form factor the Dell OptiPlex 5000 M is the right one for you. It is smaller than the HP ProDesk 600 G3 Microtower and will fit more easily under your desk.
Processor
Usually the newer the generation of the CPU, the better the performance and efficiency is. If your budget allows it, you should go with the Dell OptiPlex 5000 M as it is running a newer generation CPU. This is not to say that HP ProDesk 600 G3 Microtower is bad - it can still run some powerful CPUs, albeit being an older generation.
Memory
The HP ProDesk 600 G3 Microtower has 4 RAM slots while the Dell OptiPlex 5000 M has only 2 slot(s). This is not something to worry about. Just make sure you take it into consideration when planning how much RAM you are going to use.
The Dell OptiPlex 5000 M is using the faster 3200 MT/s RAM. The HP ProDesk 600 G3 Microtower is slower by supporting RAM speeds of up to 2400 MT/s. In addition, you will be able to install the same amount of RAM in both models, and most probably 64 GB of RAM will be enough for most people. However, if you will be needing more RAM, make sure to check other desktop models too.
Ports
In total the HP ProDesk 600 G3 Microtower has 11 USB ports. The Dell OptiPlex 5000 M is inferior in this regard and packs 6 USB ports. In any case, if you miss USB ports, you can always purchase a USB hub. What is nice about the Dell OptiPlex 5000 M, is that it has 1 USB 3.1 port(s) which allows transfer of up to 10Gb/s. Unfortunately, the HP ProDesk 600 G3 Microtower has no such port, thus restricting your transfer speeds significantly. For people who want to use external drives on regular basis, this might be an issue.
The DisplayPort is usually the more popular video port used with desktops and laptops, while the HDMI is used predominantly in consumer electronics. That's why, it is good to see that both of the models come with a DisplayPort.
None of the models has an HDMI port. If your monitor supports only the HDMI interface, you will need to buy an adapter. Such adapters are cheap so nothing to worry about.
SATA ports are placed on the system board and it is where you connect your HDD, SSD and Optical Disk Drives. More SATA slots will allow you to have more drives running at the same time. In this regard the HP ProDesk 600 G3 Microtower is better equipped as it comes with 5 SATA slot(s), while the Dell OptiPlex 5000 M has 0 slot(s).
An M.2 SSD can be several times faster than a SATA one. Thus, we are happy to see that both models support the M.2 interface. However, the Dell OptiPlex 5000 M has 1 M.2 slots while the HP ProDesk 600 G3 Microtower comes with just 1.
Make sure that the available M.2 slot supports the PCIe (also called NVMe) interface. This is important as there are M.2 slots which support only the inferior SATA III interface. For comparison, the SATA III interface has max speeds of 6Gb/s, while the PCIe 3.0 x4 will support speeds up to 32Gb/s!
Power Supply
Having a Power Supply Unit with high power rating is important, if you are going to use components which require extra power. The Dell OptiPlex 5000 M comes with a decent 180 Watt PSU, but the HP ProDesk 600 G3 Microtower has a more powerful one rated at 250 Watts. Choosing either one depends on your specific requirements and use case. Also don't forget that some models might have more than one PSU option - try to always get the most powerful one, especially if you plan to upgrade to a powerful GPU.
Motherboard
