Dell OptiPlex 390 SFF vs. Dell OptiPlex 7010 USFF
Comparison and Differences
Differences between Dell OptiPlex 390 SFF and Dell OptiPlex 7010 USFF
If you are looking for a more modern desktop, then you should go with the Dell OptiPlex 7010 USFF which was released in 2012. The Dell OptiPlex 390 SFF is older and entered production in 2011.
If you are looking for the smaller form factor the Dell OptiPlex 7010 USFF is the right one for you. It is smaller than the Dell OptiPlex 390 SFF and will fit more easily under your desk.
Processor
Usually the newer the generation of the CPU, the better the performance and efficiency is. If your budget allows it, you should go with the Dell OptiPlex 7010 USFF as it is running a newer generation CPU. This is not to say that Dell OptiPlex 390 SFF is bad - it can still run some powerful CPUs, albeit being an older generation.
Memory
Both models have have equal amount of ram slots (2 RAM). Usually two RAM slots are more than enough for most cases. However, the count should be taken into account when planning how much and what combination of RAM you are going to need for your system.
The Dell OptiPlex 7010 USFF is using the faster 1600 MT/s RAM. The Dell OptiPlex 390 SFF is slower by supporting RAM speeds of up to 1333 MT/s. Additionally, if you will be needing a lot of RAM, better go for the Dell OptiPlex 7010 USFF as it has the ability to run 16 GB of RAM. The Dell OptiPlex 390 SFF can do a bit less at max 8 GB. Most of the times, this should be sufficient for the majority of users.
Ports
In total the Dell OptiPlex 390 SFF has 8 USB ports. The Dell OptiPlex 7010 USFF is inferior in this regard and packs 6 USB ports. In any case, if you miss USB ports, you can always purchase a USB hub. None of the desktop models has a USB 3.1 port (10Gb/s), so if you need a fast connection to your peripherals, like external Solid State Drive, you will need to look elsewhere.
Unfortunately, only the Dell OptiPlex 7010 USFF has a DisplayPort. The Dell OptiPlex 390 SFF does not have one? Don't worry though, nowadays video adapters are cheap and you can get almost any combination of conversion types.
The Dell OptiPlex 390 SFF comes with an HDMI port, while the Dell OptiPlex 7010 USFF does not support the interface. Of course missing HDMI port is something that can be easily fixed with a good adapter (e.g. DisplayPort to HDMI).
SATA slots are located on the motherboard and it is where SSD, HDD and Optical Disk Drives are connected. Each of the two models being compared have 2 SATA slot(s). Keep in mind that having too few SATA slots might limit your options for connecting additional memory drives.
M.2 SSD interface allows you to transfer data with higher speeds compared to the old SATA interface. Unfortunately, neither the Dell OptiPlex 390 SFF, nor the Dell OptiPlex 7010 USFF has one. However, you can still use a SATA SSD drive which should give you satisfactory performance.
Make sure that the available M.2 slot supports the PCIe (also called NVMe) interface. This is important as there are M.2 slots which support only the inferior SATA III interface. For comparison, the SATA III interface has max speeds of 6Gb/s, while the PCIe 3.0 x4 will support speeds up to 32Gb/s!
Power Supply
Having a Power Supply Unit with high power rating is important, if you are going to use components which require extra power. The Dell OptiPlex 7010 USFF comes with a decent 200 Watt PSU, but the Dell OptiPlex 390 SFF has a more powerful one rated at 240 Watts. Choosing either one depends on your specific requirements and use case. Also don't forget that some models might have more than one PSU option - try to always get the most powerful one, especially if you plan to upgrade to a powerful GPU.
Motherboard
