Dell OptiPlex 7070 SFF vs. HP ProDesk 400 G6 Microtower
Comparison and Differences
Differences between Dell OptiPlex 7070 SFF and HP ProDesk 400 G6 Microtower
If you are looking for a more modern desktop, then you should go with the Dell OptiPlex 7070 SFF which was released in 2019. The HP ProDesk 400 G6 Microtower is older and entered production in 2018.
If you are looking for the smaller form factor the Dell OptiPlex 7070 SFF is the right one for you. It is smaller than the HP ProDesk 400 G6 Microtower and will fit more easily under your desk.
Processor
Usually the newer the generation of the CPU, the better the performance and efficiency is. If your budget allows it, you should go with the Dell OptiPlex 7070 SFF as it is running a newer generation CPU. This is not to say that HP ProDesk 400 G6 Microtower is bad - it can still run some powerful CPUs, albeit being an older generation.
Memory
The Dell OptiPlex 7070 SFF has 4 RAM slots while the HP ProDesk 400 G6 Microtower has only 2 slot(s). This is not something to worry about. Just make sure you take it into consideration when planning how much RAM you are going to use.
None of the desktops has an advantage when it comes to the speed of the RAM being used. Both models support RAM speeds of up to 2666. In addition, you will be able to install the same amount of RAM in both models, and most probably 64 GB of RAM will be enough for most people. However, if you will be needing more RAM, make sure to check other desktop models too.
Ports
In total the Dell OptiPlex 7070 SFF has 10 USB ports. The HP ProDesk 400 G6 Microtower is inferior in this regard and packs 8 USB ports. In any case, if you miss USB ports, you can always purchase a USB hub. What is nice about the Dell OptiPlex 7070 SFF, is that it has 1 USB 3.1 port(s) which allows transfer of up to 10Gb/s. Unfortunately, the HP ProDesk 400 G6 Microtower has no such port, thus restricting your transfer speeds significantly. For people who want to use external drives on regular basis, this might be an issue.
DisplayPort is crucial for any desktop machine. It is good to see that both models are featuring DisplayPorts. However, the Dell OptiPlex 7070 SFF comes with 2 ports, while the HP ProDesk 400 G6 Microtower has only 1. If you are planning to use multiple monitors, the Dell OptiPlex 7070 SFF is the better choice.
None of the models has an HDMI port. If your monitor supports only the HDMI interface, you will need to buy an adapter. Such adapters are cheap so nothing to worry about.
SATA slots are located on the motherboard and it is where SSD, HDD and Optical Disk Drives are connected. Each of the two models being compared have 3 SATA slot(s). Keep in mind that having too few SATA slots might limit your options for connecting additional memory drives.
When your goal is to have the fastest SSD transfer speeds, an M.2 interface is crucial. Thus, it is good that both models have M.2 SSD slots. Today M.2 SSDs are not much more expensive than the average SATA drives, so it really does not make sense to invest in SATA drives anymore.
Make sure that the available M.2 slot supports the PCIe (also called NVMe) interface. This is important as there are M.2 slots which support only the inferior SATA III interface. For comparison, the SATA III interface has max speeds of 6Gb/s, while the PCIe 3.0 x4 will support speeds up to 32Gb/s!
Power Supply
Having a Power Supply Unit with high power rating is important, if you are going to use components which require extra power. The Dell OptiPlex 7070 SFF comes with a decent 200 Watt PSU, but the HP ProDesk 400 G6 Microtower has a more powerful one rated at 310 Watts. Choosing either one depends on your specific requirements and use case. Also don't forget that some models might have more than one PSU option - try to always get the most powerful one, especially if you plan to upgrade to a powerful GPU.
Motherboard
