Dell OptiPlex 7070M vs. HP ProDesk 400 G1 SFF
Comparison and Differences
Differences between Dell OptiPlex 7070M and HP ProDesk 400 G1 SFF
If you are looking for a more modern desktop, then you should go with the Dell OptiPlex 7070M which was released in 2019. The HP ProDesk 400 G1 SFF is older and entered production in 2013.
If you are looking for the smaller form factor the Dell OptiPlex 7070M is the right one for you. It is smaller than the HP ProDesk 400 G1 SFF and will fit more easily under your desk.
Processor
Usually the newer the generation of the CPU, the better the performance and efficiency is. If your budget allows it, you should go with the Dell OptiPlex 7070M as it is running a newer generation CPU. This is not to say that HP ProDesk 400 G1 SFF is bad - it can still run some powerful CPUs, albeit being an older generation.
Memory
Both models have have equal amount of ram slots (2 RAM). Usually two RAM slots are more than enough for most cases. However, the count should be taken into account when planning how much and what combination of RAM you are going to need for your system.
The Dell OptiPlex 7070M is using the faster 2666 MT/s RAM. The HP ProDesk 400 G1 SFF is slower by supporting RAM speeds of up to 1600 MT/s. Additionally, if you will be needing a lot of RAM, better go for the Dell OptiPlex 7070M as it has the ability to run 32 GB of RAM. The HP ProDesk 400 G1 SFF can do a bit less at max 16 GB. Most of the times, this should be sufficient for the majority of users.
Ports
In total the HP ProDesk 400 G1 SFF has 8 USB ports. The Dell OptiPlex 7070M is inferior in this regard and packs 6 USB ports. In any case, if you miss USB ports, you can always purchase a USB hub. What is nice about the Dell OptiPlex 7070M, is that it has 1 USB 3.1 port(s) which allows transfer of up to 10Gb/s. Unfortunately, the HP ProDesk 400 G1 SFF has no such port, thus restricting your transfer speeds significantly. For people who want to use external drives on regular basis, this might be an issue.
Unfortunately, only the Dell OptiPlex 7070M has a DisplayPort. The HP ProDesk 400 G1 SFF does not have one? Don't worry though, nowadays video adapters are cheap and you can get almost any combination of conversion types.
None of the models has an HDMI port. If your monitor supports only the HDMI interface, you will need to buy an adapter. Such adapters are cheap so nothing to worry about.
SATA ports are placed on the system board and it is where you connect your HDD, SSD and Optical Disk Drives. More SATA slots will allow you to have more drives running at the same time. In this regard the HP ProDesk 400 G1 SFF is better equipped as it comes with 3 SATA slot(s), while the Dell OptiPlex 7070M has 1 slot(s).
If you want the fastest transfer speeds for your SSD, an M.2 interface is crucial. Thus, if the M.2 SSD slot is a mandatory requirement for you, go with the Dell OptiPlex 7070M. Sadly, the HP ProDesk 400 G1 SFF has no such slot, and you will be forced to use the SATA interface instead.
Make sure that the available M.2 slot supports the PCIe (also called NVMe) interface. This is important as there are M.2 slots which support only the inferior SATA III interface. For comparison, the SATA III interface has max speeds of 6Gb/s, while the PCIe 3.0 x4 will support speeds up to 32Gb/s!
Power Supply
Having a Power Supply Unit with high power rating is important, if you are going to use components which require extra power. The Dell OptiPlex 7070M comes with a decent 130 Watt PSU, but the HP ProDesk 400 G1 SFF has a more powerful one rated at 240 Watts. Choosing either one depends on your specific requirements and use case. Also don't forget that some models might have more than one PSU option - try to always get the most powerful one, especially if you plan to upgrade to a powerful GPU.
Motherboard
