Dell OptiPlex 7080M vs. HP ProDesk 600 G4 SFF

Comparison and Differences

Dell_OptiPlex_7080M.jpg case front and back pannelHP_ProDesk_600_G4_SFF.jpg case front and back pannel
Model
Form factorMicroSmall
CPU optionsIntel Gen10 i3/i5/i7/i9;Intel Gen8 i3/i5/i7; Celeron; Pentium;
ChipsetQ470Q370
Dedicated GPU *N.A.GeForce GT 1030 Low Profile
RAMSODIMM DDR4-2666/2933DIMM DDR4-2666
RAM slots24
RAM speed2933 MT/s2666 MT/s
RAM max64 GB64 GB
USB portsUSB 3.1 Type C; (3x) USB-A 3.1; (2x) USB-A 3.0;USB-C 3.1; (4x)USB-A 3.1; (2x)USB-A 3.0; (4x)USB-A 2.0;
Video ports(2x) Display Port 1.4;(2x) DisplayPort:
Other portsRJ45; Headset; Line-Out/In;RJ45; Headset; Line-Out; Line-In;
Optional portsHDMI2.0b/DP1.4/VGA/USB Type-C (DP Alt Mode); Serial; Serial+PS2; (2x) WiFi antenna;DP1.2/HDMI2.0/VGA/USB-C(DP); Serial; SD card reader;
SATA ports13
PCI slotsPCIe x8 Gen3 (optional) PCIe 3.0 x16; PCIe x4 (open ended);
M.2 slotsM.2 2280/2230 M-key (PCIe 3.0 x4, NVMe); M.2 2280 M-key (PCIe); M.2 2230 (WiFi/BT) M.2 2280/2230 M-key (PCIe x4); M.2 2230 (WiFi/BT);
Drive bays2.5in(2x)2.5in/3.5in; 5.25in (slim);
PSU90/130/180 W180 W
Weight1.38 kg (3.04 lb)4.54 kg (10.01 lb)
Released20202018
Manuallinklink
Price**Check PriceCheck Price

** As an Amazon associate we earn from qualifying purchases.
* Dedicated GPU warning: Check if your particular power supply model has enough power. Additionally some PSUs don't come with an auxiliary PCIe power connector and you may need to buy a SATA to PCIe power adapter.

Differences between Dell OptiPlex 7080M and HP ProDesk 600 G4 SFF

If you are looking for a more modern desktop, then you should go with the Dell OptiPlex 7080M which was released in 2020. The HP ProDesk 600 G4 SFF is older and entered production in 2018.

If you are looking for the smaller form factor the Dell OptiPlex 7080M is the right one for you. It is smaller than the HP ProDesk 600 G4 SFF and will fit more easily under your desk.

Processor

Usually the newer the generation of the CPU, the better the performance and efficiency is. If your budget allows it, you should go with the Dell OptiPlex 7080M as it is running a newer generation CPU. This is not to say that HP ProDesk 600 G4 SFF is bad - it can still run some powerful CPUs, albeit being an older generation.

Memory

The HP ProDesk 600 G4 SFF has 4 RAM slots while the Dell OptiPlex 7080M has only 2 slot(s). This is not something to worry about. Just make sure you take it into consideration when planning how much RAM you are going to use.

The Dell OptiPlex 7080M is using the faster 2933 MT/s RAM. The HP ProDesk 600 G4 SFF is slower by supporting RAM speeds of up to 2666 MT/s. In addition, you will be able to install the same amount of RAM in both models, and most probably 64 GB of RAM will be enough for most people. However, if you will be needing more RAM, make sure to check other desktop models too.

Ports

In total the HP ProDesk 600 G4 SFF has 11 USB ports. The Dell OptiPlex 7080M is inferior in this regard and packs 6 USB ports. In any case, if you miss USB ports, you can always purchase a USB hub. It's great that both of the models have USB 3.1 ports which will allow you to exchange data with your peripherals at up to 10Gb/s. But if you need maximum connectivity, go with the HP ProDesk 600 G4 SFF as it has 5 USB3.1 ports (the Dell OptiPlex 7080M has 4).

The DisplayPort is usually the more popular video port used with desktops and laptops, while the HDMI is used predominantly in consumer electronics. That's why, it is good to see that both of the models come with a DisplayPort.

None of the models has an HDMI port. If your monitor supports only the HDMI interface, you will need to buy an adapter. Such adapters are cheap so nothing to worry about.

SATA ports are placed on the system board and it is where you connect your HDD, SSD and Optical Disk Drives. More SATA slots will allow you to have more drives running at the same time. In this regard the HP ProDesk 600 G4 SFF is better equipped as it comes with 3 SATA slot(s), while the Dell OptiPlex 7080M has 1 slot(s).

An M.2 SSD can be several times faster than a SATA one. Thus, we are happy to see that both models support the M.2 interface. However, the Dell OptiPlex 7080M has 1 M.2 slots while the HP ProDesk 600 G4 SFF comes with just 1.

Make sure that the available M.2 slot supports the PCIe (also called NVMe) interface. This is important as there are M.2 slots which support only the inferior SATA III interface. For comparison, the SATA III interface has max speeds of 6Gb/s, while the PCIe 3.0 x4 will support speeds up to 32Gb/s!

Power Supply

Looking at the Power Supply Unit (PSU) of the two models we don't see any differences. For either of them you get a maximum power of 180 Watts. However be careful, many models have more than one power supply option. When buying your computer, it is a good idea to get a version with the most powerful PSU. This will potentially allow you to upgrade to a more powerful GPU for example.

Motherboard

Dell_OptiPlex_7080M_motherboard.jpg motherboard layoutHP_ProDesk_600_G4_SFF_motherboard.jpg motherboard layout