Dell OptiPlex 5070 MT vs. Fujitsu Esprimo D9010
Comparison and Differences
Differences between Dell OptiPlex 5070 MT and Fujitsu Esprimo D9010
If you are looking for a more modern desktop, then you should go with the Fujitsu Esprimo D9010 which was released in 2020. The Dell OptiPlex 5070 MT is older and entered production in 2019.
If you are looking for the smaller form factor the Fujitsu Esprimo D9010 is the right one for you. It is smaller than the Dell OptiPlex 5070 MT and will fit more easily under your desk.
Processor
Usually the newer the generation of the CPU, the better the performance and efficiency is. If your budget allows it, you should go with the Fujitsu Esprimo D9010 as it is running a newer generation CPU. This is not to say that Dell OptiPlex 5070 MT is bad - it can still run some powerful CPUs, albeit being an older generation.
Memory
Both models have have equal amount of ram slots (4 RAM). Usually two RAM slots are more than enough for most cases. However, the count should be taken into account when planning how much and what combination of RAM you are going to need for your system.
The Fujitsu Esprimo D9010 is using the faster 2933 MT/s RAM. The Dell OptiPlex 5070 MT is slower by supporting RAM speeds of up to 2666 MT/s. Additionally, if you will be needing a lot of RAM, better go for the Fujitsu Esprimo D9010 as it has the ability to run 128 GB of RAM. The Dell OptiPlex 5070 MT can do a bit less at max 64 GB. Most of the times, this should be sufficient for the majority of users.
Ports
In total the Fujitsu Esprimo D9010 has 11 USB ports. The Dell OptiPlex 5070 MT is inferior in this regard and packs 10 USB ports. In any case, if you miss USB ports, you can always purchase a USB hub. It's great that both of the models have USB 3.1 ports which will allow you to exchange data with your peripherals at up to 10Gb/s. But if you need maximum connectivity, go with the Fujitsu Esprimo D9010 as it has 4 USB3.1 ports (the Dell OptiPlex 5070 MT has 1).
The DisplayPort is usually the more popular video port used with desktops and laptops, while the HDMI is used predominantly in consumer electronics. That's why, it is good to see that both of the models come with a DisplayPort.
None of the models has an HDMI port. If your monitor supports only the HDMI interface, you will need to buy an adapter. Such adapters are cheap so nothing to worry about.
SATA slots are located on the motherboard and it is where SSD, HDD and Optical Disk Drives are connected. Each of the two models being compared have 4 SATA slot(s). Keep in mind that having too few SATA slots might limit your options for connecting additional memory drives.
An M.2 SSD can be several times faster than a SATA one. Thus, we are happy to see that both models support the M.2 interface. However, the Fujitsu Esprimo D9010 has 1 M.2 slots while the Dell OptiPlex 5070 MT comes with just 1.
Make sure that the available M.2 slot supports the PCIe (also called NVMe) interface. This is important as there are M.2 slots which support only the inferior SATA III interface. For comparison, the SATA III interface has max speeds of 6Gb/s, while the PCIe 3.0 x4 will support speeds up to 32Gb/s!
Power Supply
Having a Power Supply Unit with high power rating is important, if you are going to use components which require extra power. The Dell OptiPlex 5070 MT comes with a decent 260 Watt PSU, but the Fujitsu Esprimo D9010 has a more powerful one rated at 300 Watts. Choosing either one depends on your specific requirements and use case. Also don't forget that some models might have more than one PSU option - try to always get the most powerful one, especially if you plan to upgrade to a powerful GPU.
Motherboard
