Dell OptiPlex 7000 Tower vs. Fujitsu Esprimo D9010
Comparison and Differences
Differences between Dell OptiPlex 7000 Tower and Fujitsu Esprimo D9010
If you are looking for a more modern desktop, then you should go with the Dell OptiPlex 7000 Tower which was released in 2022. The Fujitsu Esprimo D9010 is older and entered production in 2020.
If you are looking for the smaller form factor the Fujitsu Esprimo D9010 is the right one for you. It is smaller than the Dell OptiPlex 7000 Tower and will fit more easily under your desk.
Processor
Usually the newer the generation of the CPU, the better the performance and efficiency is. If your budget allows it, you should go with the Dell OptiPlex 7000 Tower as it is running a newer generation CPU. This is not to say that Fujitsu Esprimo D9010 is bad - it can still run some powerful CPUs, albeit being an older generation.
Memory
Both models have have equal amount of ram slots (4 RAM). Usually two RAM slots are more than enough for most cases. However, the count should be taken into account when planning how much and what combination of RAM you are going to need for your system.
The Dell OptiPlex 7000 Tower is using the faster 4400 MT/s RAM. The Fujitsu Esprimo D9010 is slower by supporting RAM speeds of up to 2933 MT/s. In addition, you will be able to install the same amount of RAM in both models, and most probably 128 GB of RAM will be enough for most people. However, if you will be needing more RAM, make sure to check other desktop models too.
Ports
In total the Fujitsu Esprimo D9010 has 11 USB ports. The Dell OptiPlex 7000 Tower is inferior in this regard and packs 10 USB ports. In any case, if you miss USB ports, you can always purchase a USB hub. It's great that both of the models have USB 3.1 ports which will allow you to exchange data with your peripherals at up to 10Gb/s. But if you need maximum connectivity, go with the Fujitsu Esprimo D9010 as it has 4 USB3.1 ports (the Dell OptiPlex 7000 Tower has 2).
DisplayPort is crucial for any desktop machine. It is good to see that both models are featuring DisplayPorts. However, the Dell OptiPlex 7000 Tower comes with 3 ports, while the Fujitsu Esprimo D9010 has only 2. If you are planning to use multiple monitors, the Dell OptiPlex 7000 Tower is the better choice.
None of the models has an HDMI port. If your monitor supports only the HDMI interface, you will need to buy an adapter. Such adapters are cheap so nothing to worry about.
SATA slots are located on the motherboard and it is where SSD, HDD and Optical Disk Drives are connected. Each of the two models being compared have 4 SATA slot(s). Keep in mind that having too few SATA slots might limit your options for connecting additional memory drives.
An M.2 SSD can be several times faster than a SATA one. Thus, we are happy to see that both models support the M.2 interface. However, the Dell OptiPlex 7000 Tower has 2 M.2 slots while the Fujitsu Esprimo D9010 comes with just 2.
Make sure that the available M.2 slot supports the PCIe (also called NVMe) interface. This is important as there are M.2 slots which support only the inferior SATA III interface. For comparison, the SATA III interface has max speeds of 6Gb/s, while the PCIe 3.0 x4 will support speeds up to 32Gb/s!
Power Supply
Having a Power Supply Unit with high power rating is important, if you are going to use components which require extra power. The Fujitsu Esprimo D9010 comes with a decent 300 Watt PSU, but the Dell OptiPlex 7000 Tower has a more powerful one rated at 500 Watts. Choosing either one depends on your specific requirements and use case. Also don't forget that some models might have more than one PSU option - try to always get the most powerful one, especially if you plan to upgrade to a powerful GPU.
Motherboard
