Fujitsu Esprimo E410 vs. Fujitsu Esprimo G558
Comparison and Differences
Differences between Fujitsu Esprimo E410 and Fujitsu Esprimo G558
If you are looking for a more modern desktop, then you should go with the Fujitsu Esprimo G558 which was released in 2018. The Fujitsu Esprimo E410 is older and entered production in 2014.
If you are looking for the smaller form factor the Fujitsu Esprimo G558 is the right one for you. It is smaller than the Fujitsu Esprimo E410 and will fit more easily under your desk.
Processor
Usually the newer the generation of the CPU, the better the performance and efficiency is. If your budget allows it, you should go with the Fujitsu Esprimo G558 as it is running a newer generation CPU. This is not to say that Fujitsu Esprimo E410 is bad - it can still run some powerful CPUs, albeit being an older generation.
Memory
Both models have have equal amount of ram slots (2 RAM). Usually two RAM slots are more than enough for most cases. However, the count should be taken into account when planning how much and what combination of RAM you are going to need for your system.
The Fujitsu Esprimo G558 is using the faster 2666 MT/s RAM. The Fujitsu Esprimo E410 is slower by supporting RAM speeds of up to 1600 MT/s. In addition, you will be able to install the same amount of RAM in both models, and most probably 32 GB of RAM will be enough for most people. However, if you will be needing more RAM, make sure to check other desktop models too.
Ports
Both models have the same amount of USB ports for total count of 6. If this is not enough, using a USB hub is always a viable option. None of the desktop models has a USB 3.1 port (10Gb/s), so if you need a fast connection to your peripherals, like external Solid State Drive, you will need to look elsewhere.
Unfortunately, only the Fujitsu Esprimo G558 has a DisplayPort. The Fujitsu Esprimo E410 does not have one? Don't worry though, nowadays video adapters are cheap and you can get almost any combination of conversion types.
The Fujitsu Esprimo G558 comes with an HDMI port, while the Fujitsu Esprimo E410 does not support the interface. Of course missing HDMI port is something that can be easily fixed with a good adapter (e.g. DisplayPort to HDMI).
SATA ports are placed on the system board and it is where you connect your HDD, SSD and Optical Disk Drives. More SATA slots will allow you to have more drives running at the same time. In this regard the Fujitsu Esprimo E410 is better equipped as it comes with 3 SATA slot(s), while the Fujitsu Esprimo G558 has 1 slot(s).
If you want the fastest transfer speeds for your SSD, an M.2 interface is crucial. Thus, if the M.2 SSD slot is a mandatory requirement for you, go with the Fujitsu Esprimo G558. Sadly, the Fujitsu Esprimo E410 has no such slot, and you will be forced to use the SATA interface instead.
Make sure that the available M.2 slot supports the PCIe (also called NVMe) interface. This is important as there are M.2 slots which support only the inferior SATA III interface. For comparison, the SATA III interface has max speeds of 6Gb/s, while the PCIe 3.0 x4 will support speeds up to 32Gb/s!
Power Supply
Having a Power Supply Unit with high power rating is important, if you are going to use components which require extra power. The Fujitsu Esprimo G558 comes with a decent 65 Watt PSU, but the Fujitsu Esprimo E410 has a more powerful one rated at 280 Watts. Choosing either one depends on your specific requirements and use case. Also don't forget that some models might have more than one PSU option - try to always get the most powerful one, especially if you plan to upgrade to a powerful GPU.
Motherboard
