Fujitsu Esprimo E920 vs. HP ProDesk 600 G2 Microtower

Differences between Fujitsu Esprimo E920 and HP ProDesk 600 G2 Microtower

If you are looking for a more modern desktop, then you should go with the HP ProDesk 600 G2 Microtower which was released in 2015. The Fujitsu Esprimo E920 is older and entered production in 2014.

If you are looking for the smaller form factor the Fujitsu Esprimo E920 is the right one for you. It is smaller than the HP ProDesk 600 G2 Microtower and will fit more easily under your desk.

Processor

Usually the newer the generation of the CPU, the better the performance and efficiency is. If your budget allows it, you should go with the HP ProDesk 600 G2 Microtower as it is running a newer generation CPU. This is not to say that Fujitsu Esprimo E920 is bad - it can still run some powerful CPUs, albeit being an older generation.

Memory

Both models have have equal amount of ram slots (4 RAM). Usually two RAM slots are more than enough for most cases. However, the count should be taken into account when planning how much and what combination of RAM you are going to need for your system.

The HP ProDesk 600 G2 Microtower is using the faster 2133 MT/s RAM. The Fujitsu Esprimo E920 is slower by supporting RAM speeds of up to 1600 MT/s. Additionally, if you will be needing a lot of RAM, better go for the HP ProDesk 600 G2 Microtower as it has the ability to run 64 GB of RAM. The Fujitsu Esprimo E920 can do a bit less at max 32 GB. Most of the times, this should be sufficient for the majority of users.

Ports

In total the Fujitsu Esprimo E920 has 12 USB ports. The HP ProDesk 600 G2 Microtower is inferior in this regard and packs 10 USB ports. In any case, if you miss USB ports, you can always purchase a USB hub. None of the desktop models has a USB 3.1 port (10Gb/s), so if you need a fast connection to your peripherals, like external Solid State Drive, you will need to look elsewhere.

DisplayPort is crucial for any desktop machine. It is good to see that both models are featuring DisplayPorts. However, the HP ProDesk 600 G2 Microtower comes with 2 ports, while the Fujitsu Esprimo E920 has only 1. If you are planning to use multiple monitors, the HP ProDesk 600 G2 Microtower is the better choice.

None of the models has an HDMI port. If your monitor supports only the HDMI interface, you will need to buy an adapter. Such adapters are cheap so nothing to worry about.

SATA ports are placed on the system board and it is where you connect your HDD, SSD and Optical Disk Drives. More SATA slots will allow you to have more drives running at the same time. In this regard the Fujitsu Esprimo E920 is better equipped as it comes with 6 SATA slot(s), while the HP ProDesk 600 G2 Microtower has 3 slot(s).

M.2 SSD interface allows you to transfer data with higher speeds compared to the old SATA interface. Unfortunately, neither the HP ProDesk 600 G2 Microtower, nor the Fujitsu Esprimo E920 has one. However, you can still use a SATA SSD drive which should give you satisfactory performance.

Make sure that the available M.2 slot supports the PCIe (also called NVMe) interface. This is important as there are M.2 slots which support only the inferior SATA III interface. For comparison, the SATA III interface has max speeds of 6Gb/s, while the PCIe 3.0 x4 will support speeds up to 32Gb/s!

Power Supply

Looking at the Power Supply Unit (PSU) of the two models we don't see any differences. For either of them you get a maximum power of 280 Watts. However be careful, many models have more than one power supply option. When buying your computer, it is a good idea to get a version with the most powerful PSU. This will potentially allow you to upgrade to a more powerful GPU for example.

Motherboard