Dell XPS 8300 vs. Fujitsu Esprimo G5011
Comparison and Differences
Differences between Dell XPS 8300 and Fujitsu Esprimo G5011
If you are looking for a more modern desktop, then you should go with the Fujitsu Esprimo G5011 which was released in 2021. The Dell XPS 8300 is older and entered production in 2011.
If you are looking for the smaller form factor the Fujitsu Esprimo G5011 is the right one for you. It is smaller than the Dell XPS 8300 and will fit more easily under your desk.
Processor
Usually the newer the generation of the CPU, the better the performance and efficiency is. If your budget allows it, you should go with the Fujitsu Esprimo G5011 as it is running a newer generation CPU. This is not to say that Dell XPS 8300 is bad - it can still run some powerful CPUs, albeit being an older generation.
Memory
The Dell XPS 8300 has 4 RAM slots while the Fujitsu Esprimo G5011 has only 2 slot(s). This is not something to worry about. Just make sure you take it into consideration when planning how much RAM you are going to use.
The Fujitsu Esprimo G5011 is using the faster 3200 MT/s RAM. The Dell XPS 8300 is slower by supporting RAM speeds of up to 1600 MT/s. Additionally, if you will be needing a lot of RAM, better go for the Fujitsu Esprimo G5011 as it has the ability to run 64 GB of RAM. The Dell XPS 8300 can do a bit less at max 32 GB. Most of the times, this should be sufficient for the majority of users.
Ports
In total the Dell XPS 8300 has 10 USB ports. The Fujitsu Esprimo G5011 is inferior in this regard and packs 6 USB ports. In any case, if you miss USB ports, you can always purchase a USB hub. None of the desktop models has a USB 3.1 port (10Gb/s), so if you need a fast connection to your peripherals, like external Solid State Drive, you will need to look elsewhere.
Unfortunately, only the Fujitsu Esprimo G5011 has a DisplayPort. The Dell XPS 8300 does not have one? Don't worry though, nowadays video adapters are cheap and you can get almost any combination of conversion types.
In case your monitor supports HDMI only, you will be happy to hear that both models come with an HDMI port.
SATA ports are placed on the system board and it is where you connect your HDD, SSD and Optical Disk Drives. More SATA slots will allow you to have more drives running at the same time. In this regard the Dell XPS 8300 is better equipped as it comes with 4 SATA slot(s), while the Fujitsu Esprimo G5011 has 1 slot(s).
If you want the fastest transfer speeds for your SSD, an M.2 interface is crucial. Thus, if the M.2 SSD slot is a mandatory requirement for you, go with the Fujitsu Esprimo G5011. Sadly, the Dell XPS 8300 has no such slot, and you will be forced to use the SATA interface instead.
Make sure that the available M.2 slot supports the PCIe (also called NVMe) interface. This is important as there are M.2 slots which support only the inferior SATA III interface. For comparison, the SATA III interface has max speeds of 6Gb/s, while the PCIe 3.0 x4 will support speeds up to 32Gb/s!
Power Supply
Having a Power Supply Unit with high power rating is important, if you are going to use components which require extra power. The Fujitsu Esprimo G5011 comes with a decent 65 Watt PSU, but the Dell XPS 8300 has a more powerful one rated at 460 Watts. Choosing either one depends on your specific requirements and use case. Also don't forget that some models might have more than one PSU option - try to always get the most powerful one, especially if you plan to upgrade to a powerful GPU.
Motherboard
