Dell OptiPlex 7080M vs. Fujitsu Esprimo P5011
Comparison and Differences
Differences between Dell OptiPlex 7080M and Fujitsu Esprimo P5011
If you are looking for a more modern desktop, then you should go with the Fujitsu Esprimo P5011 which was released in 2021. The Dell OptiPlex 7080M is older and entered production in 2020.
If you are looking for the smaller form factor the Dell OptiPlex 7080M is the right one for you. It is smaller than the Fujitsu Esprimo P5011 and will fit more easily under your desk.
Processor
Usually the newer the generation of the CPU, the better the performance and efficiency is. If your budget allows it, you should go with the Fujitsu Esprimo P5011 as it is running a newer generation CPU. This is not to say that Dell OptiPlex 7080M is bad - it can still run some powerful CPUs, albeit being an older generation.
Memory
Both models have have equal amount of ram slots (2 RAM). Usually two RAM slots are more than enough for most cases. However, the count should be taken into account when planning how much and what combination of RAM you are going to need for your system.
The Fujitsu Esprimo P5011 is using the faster 3200 MT/s RAM. The Dell OptiPlex 7080M is slower by supporting RAM speeds of up to 2933 MT/s. In addition, you will be able to install the same amount of RAM in both models, and most probably 64 GB of RAM will be enough for most people. However, if you will be needing more RAM, make sure to check other desktop models too.
Ports
Both models have the same amount of USB ports for total count of 6. If this is not enough, using a USB hub is always a viable option. What is nice about the Dell OptiPlex 7080M, is that it has 4 USB 3.1 port(s) which allows transfer of up to 10Gb/s. Unfortunately, the Fujitsu Esprimo P5011 has no such port, thus restricting your transfer speeds significantly. For people who want to use external drives on regular basis, this might be an issue.
DisplayPort is crucial for any desktop machine. It is good to see that both models are featuring DisplayPorts. However, the Dell OptiPlex 7080M comes with 2 ports, while the Fujitsu Esprimo P5011 has only 1. If you are planning to use multiple monitors, the Dell OptiPlex 7080M is the better choice.
None of the models has an HDMI port. If your monitor supports only the HDMI interface, you will need to buy an adapter. Such adapters are cheap so nothing to worry about.
SATA ports are placed on the system board and it is where you connect your HDD, SSD and Optical Disk Drives. More SATA slots will allow you to have more drives running at the same time. In this regard the Fujitsu Esprimo P5011 is better equipped as it comes with 4 SATA slot(s), while the Dell OptiPlex 7080M has 1 slot(s).
An M.2 SSD can be several times faster than a SATA one. Thus, we are happy to see that both models support the M.2 interface. However, the Dell OptiPlex 7080M has 1 M.2 slots while the Fujitsu Esprimo P5011 comes with just 1.
Make sure that the available M.2 slot supports the PCIe (also called NVMe) interface. This is important as there are M.2 slots which support only the inferior SATA III interface. For comparison, the SATA III interface has max speeds of 6Gb/s, while the PCIe 3.0 x4 will support speeds up to 32Gb/s!
Power Supply
Having a Power Supply Unit with high power rating is important, if you are going to use components which require extra power. The Dell OptiPlex 7080M comes with a decent 180 Watt PSU, but the Fujitsu Esprimo P5011 has a more powerful one rated at 300 Watts. Choosing either one depends on your specific requirements and use case. Also don't forget that some models might have more than one PSU option - try to always get the most powerful one, especially if you plan to upgrade to a powerful GPU.
Motherboard
