Fujitsu Esprimo P556 vs. HP ProDesk 600 G1 Microtower

Differences between Fujitsu Esprimo P556 and HP ProDesk 600 G1 Microtower

If you are looking for a more modern desktop, then you should go with the Fujitsu Esprimo P556 which was released in 2015. The HP ProDesk 600 G1 Microtower is older and entered production in 2013.

Both models have the same form factor, meaning reoughtly they have the same phiysical size and form.

Processor

Usually the newer the generation of the CPU, the better the performance and efficiency is. If your budget allows it, you should go with the Fujitsu Esprimo P556 as it is running a newer generation CPU. This is not to say that HP ProDesk 600 G1 Microtower is bad - it can still run some powerful CPUs, albeit being an older generation.

Memory

The HP ProDesk 600 G1 Microtower has 4 RAM slots while the Fujitsu Esprimo P556 has only 2 slot(s). This is not something to worry about. Just make sure you take it into consideration when planning how much RAM you are going to use.

The Fujitsu Esprimo P556 is using the faster 2133 MT/s RAM. The HP ProDesk 600 G1 Microtower is slower by supporting RAM speeds of up to 1600 MT/s. In addition, you will be able to install the same amount of RAM in both models, and most probably 32 GB of RAM will be enough for most people. However, if you will be needing more RAM, make sure to check other desktop models too.

Ports

Both models have the same amount of USB ports for total count of 10. If this is not enough, using a USB hub is always a viable option. None of the desktop models has a USB 3.1 port (10Gb/s), so if you need a fast connection to your peripherals, like external Solid State Drive, you will need to look elsewhere.

DisplayPort is crucial for any desktop machine. It is good to see that both models are featuring DisplayPorts. However, the HP ProDesk 600 G1 Microtower comes with 2 ports, while the Fujitsu Esprimo P556 has only 1. If you are planning to use multiple monitors, the HP ProDesk 600 G1 Microtower is the better choice.

None of the models has an HDMI port. If your monitor supports only the HDMI interface, you will need to buy an adapter. Such adapters are cheap so nothing to worry about.

SATA ports are placed on the system board and it is where you connect your HDD, SSD and Optical Disk Drives. More SATA slots will allow you to have more drives running at the same time. In this regard the HP ProDesk 600 G1 Microtower is better equipped as it comes with 4 SATA slot(s), while the Fujitsu Esprimo P556 has 3 slot(s).

M.2 SSD interface allows you to transfer data with higher speeds compared to the old SATA interface. Unfortunately, neither the HP ProDesk 600 G1 Microtower, nor the Fujitsu Esprimo P556 has one. However, you can still use a SATA SSD drive which should give you satisfactory performance.

Make sure that the available M.2 slot supports the PCIe (also called NVMe) interface. This is important as there are M.2 slots which support only the inferior SATA III interface. For comparison, the SATA III interface has max speeds of 6Gb/s, while the PCIe 3.0 x4 will support speeds up to 32Gb/s!

Power Supply

Having a Power Supply Unit with high power rating is important, if you are going to use components which require extra power. The Fujitsu Esprimo P556 comes with a decent 280 Watt PSU, but the HP ProDesk 600 G1 Microtower has a more powerful one rated at 320 Watts. Choosing either one depends on your specific requirements and use case. Also don't forget that some models might have more than one PSU option - try to always get the most powerful one, especially if you plan to upgrade to a powerful GPU.

Motherboard