Dell OptiPlex 5080 MT vs. Fujitsu Esprimo P710
Comparison and Differences
Differences between Dell OptiPlex 5080 MT and Fujitsu Esprimo P710
If you are looking for a more modern desktop, then you should go with the Dell OptiPlex 5080 MT which was released in 2020. The Fujitsu Esprimo P710 is older and entered production in 2014.
Both models have the same form factor, meaning reoughtly they have the same phiysical size and form.
Processor
Usually the newer the generation of the CPU, the better the performance and efficiency is. If your budget allows it, you should go with the Dell OptiPlex 5080 MT as it is running a newer generation CPU. This is not to say that Fujitsu Esprimo P710 is bad - it can still run some powerful CPUs, albeit being an older generation.
Memory
Both models have have equal amount of ram slots (4 RAM). Usually two RAM slots are more than enough for most cases. However, the count should be taken into account when planning how much and what combination of RAM you are going to need for your system.
The Dell OptiPlex 5080 MT is using the faster 2933 MT/s RAM. The Fujitsu Esprimo P710 is slower by supporting RAM speeds of up to 1600 MT/s. Additionally, if you will be needing a lot of RAM, better go for the Dell OptiPlex 5080 MT as it has the ability to run 128 GB of RAM. The Fujitsu Esprimo P710 can do a bit less at max 32 GB. Most of the times, this should be sufficient for the majority of users.
Ports
In total the Fujitsu Esprimo P710 has 12 USB ports. The Dell OptiPlex 5080 MT is inferior in this regard and packs 10 USB ports. In any case, if you miss USB ports, you can always purchase a USB hub. What is nice about the Dell OptiPlex 5080 MT, is that it has 1 USB 3.1 port(s) which allows transfer of up to 10Gb/s. Unfortunately, the Fujitsu Esprimo P710 has no such port, thus restricting your transfer speeds significantly. For people who want to use external drives on regular basis, this might be an issue.
DisplayPort is crucial for any desktop machine. It is good to see that both models are featuring DisplayPorts. However, the Dell OptiPlex 5080 MT comes with 2 ports, while the Fujitsu Esprimo P710 has only 1. If you are planning to use multiple monitors, the Dell OptiPlex 5080 MT is the better choice.
None of the models has an HDMI port. If your monitor supports only the HDMI interface, you will need to buy an adapter. Such adapters are cheap so nothing to worry about.
SATA ports are placed on the system board and it is where you connect your HDD, SSD and Optical Disk Drives. More SATA slots will allow you to have more drives running at the same time. In this regard the Fujitsu Esprimo P710 is better equipped as it comes with 5 SATA slot(s), while the Dell OptiPlex 5080 MT has 4 slot(s).
If you want the fastest transfer speeds for your SSD, an M.2 interface is crucial. Thus, if the M.2 SSD slot is a mandatory requirement for you, go with the Dell OptiPlex 5080 MT. Sadly, the Fujitsu Esprimo P710 has no such slot, and you will be forced to use the SATA interface instead.
Make sure that the available M.2 slot supports the PCIe (also called NVMe) interface. This is important as there are M.2 slots which support only the inferior SATA III interface. For comparison, the SATA III interface has max speeds of 6Gb/s, while the PCIe 3.0 x4 will support speeds up to 32Gb/s!
Power Supply
Having a Power Supply Unit with high power rating is important, if you are going to use components which require extra power. The Fujitsu Esprimo P710 comes with a decent 280 Watt PSU, but the Dell OptiPlex 5080 MT has a more powerful one rated at 360 Watts. Choosing either one depends on your specific requirements and use case. Also don't forget that some models might have more than one PSU option - try to always get the most powerful one, especially if you plan to upgrade to a powerful GPU.
Motherboard
