Fujitsu Esprimo Q556 vs. HP ProDesk 400 G1 Microtower

Comparison and Differences

Fujitsu_Esprimo_Q556.jpg case front and back pannelHP_ProDesk_400_G1_Microtower.jpg case front and back pannel
Model
Form factorMicroMini Tower
CPU optionsIntel Gen6 i3/i5/i7; PentiumIntel Gen4 i3/i5/i7; Celeron; Pentium;
ChipsetH110H81
Dedicated GPU *N.A.GeForce GTX 1660 Super
RAMSODIMM DDR4-2133DIMM DDR3-1600
RAM slots22
RAM speed2133 MT/s1600 MT/s
RAM max32 GB16 GB
USB ports(2x) USB-A 3.0; (4x) USB-A 2.0(2x)USB-A 3.0; (6x)USB-A 2.0;
Video portsDisplayPort 1.2; DVIDVI-D; VGA;
Other portsRJ45; Headphones; Mic; Line out; (1x) PS/2 RJ45; Hdph; Mic; Line-Out; Line-In; Serial; (2x) PS2;
Optional portsVGAMedia card reader (USB 2.0); Serial; Parallel;
SATA ports24
PCI slotsN.A.PCIe x16; (3x) PCIe x1;
M.2 slotsM.2 2280/2230 M-key (PCIe 2.0 x2, SSD); M.2 2230 (WiFi/BT)N.A.
Drive bays2.5in; 5.25 inch slim(3x) 3.5in; (2x) 5.25in
PSU65 W300 W
Weight1.60 kg (3.53 lb)7.1 kg (15.75 lb)
Released20152013
Manuallinklink
Price**Check PriceCheck Price

** As an Amazon associate we earn from qualifying purchases.
* Dedicated GPU warning: Check if your particular power supply model has enough power. Additionally some PSUs don't come with an auxiliary PCIe power connector and you may need to buy a SATA to PCIe power adapter.

Differences between Fujitsu Esprimo Q556 and HP ProDesk 400 G1 Microtower

If you are looking for a more modern desktop, then you should go with the Fujitsu Esprimo Q556 which was released in 2015. The HP ProDesk 400 G1 Microtower is older and entered production in 2013.

If you are looking for the smaller form factor the Fujitsu Esprimo Q556 is the right one for you. It is smaller than the HP ProDesk 400 G1 Microtower and will fit more easily under your desk.

Processor

Usually the newer the generation of the CPU, the better the performance and efficiency is. If your budget allows it, you should go with the Fujitsu Esprimo Q556 as it is running a newer generation CPU. This is not to say that HP ProDesk 400 G1 Microtower is bad - it can still run some powerful CPUs, albeit being an older generation.

Memory

Both models have have equal amount of ram slots (2 RAM). Usually two RAM slots are more than enough for most cases. However, the count should be taken into account when planning how much and what combination of RAM you are going to need for your system.

The Fujitsu Esprimo Q556 is using the faster 2133 MT/s RAM. The HP ProDesk 400 G1 Microtower is slower by supporting RAM speeds of up to 1600 MT/s. Additionally, if you will be needing a lot of RAM, better go for the Fujitsu Esprimo Q556 as it has the ability to run 32 GB of RAM. The HP ProDesk 400 G1 Microtower can do a bit less at max 16 GB. Most of the times, this should be sufficient for the majority of users.

Ports

In total the HP ProDesk 400 G1 Microtower has 8 USB ports. The Fujitsu Esprimo Q556 is inferior in this regard and packs 6 USB ports. In any case, if you miss USB ports, you can always purchase a USB hub. None of the desktop models has a USB 3.1 port (10Gb/s), so if you need a fast connection to your peripherals, like external Solid State Drive, you will need to look elsewhere.

Unfortunately, only the Fujitsu Esprimo Q556 has a DisplayPort. The HP ProDesk 400 G1 Microtower does not have one? Don't worry though, nowadays video adapters are cheap and you can get almost any combination of conversion types.

None of the models has an HDMI port. If your monitor supports only the HDMI interface, you will need to buy an adapter. Such adapters are cheap so nothing to worry about.

SATA ports are placed on the system board and it is where you connect your HDD, SSD and Optical Disk Drives. More SATA slots will allow you to have more drives running at the same time. In this regard the HP ProDesk 400 G1 Microtower is better equipped as it comes with 4 SATA slot(s), while the Fujitsu Esprimo Q556 has 2 slot(s).

If you want the fastest transfer speeds for your SSD, an M.2 interface is crucial. Thus, if the M.2 SSD slot is a mandatory requirement for you, go with the Fujitsu Esprimo Q556. Sadly, the HP ProDesk 400 G1 Microtower has no such slot, and you will be forced to use the SATA interface instead.

Make sure that the available M.2 slot supports the PCIe (also called NVMe) interface. This is important as there are M.2 slots which support only the inferior SATA III interface. For comparison, the SATA III interface has max speeds of 6Gb/s, while the PCIe 3.0 x4 will support speeds up to 32Gb/s!

Power Supply

Having a Power Supply Unit with high power rating is important, if you are going to use components which require extra power. The Fujitsu Esprimo Q556 comes with a decent 65 Watt PSU, but the HP ProDesk 400 G1 Microtower has a more powerful one rated at 300 Watts. Choosing either one depends on your specific requirements and use case. Also don't forget that some models might have more than one PSU option - try to always get the most powerful one, especially if you plan to upgrade to a powerful GPU.

Motherboard

Fujitsu_Esprimo_Q556_motherboard.jpg motherboard layoutHP_ProDesk_400_G1_Microtower_motherboard.jpg motherboard layout