Dell OptiPlex 3020M vs. HP ProDesk 490 G1 Microtower
Comparison and Differences
Differences between Dell OptiPlex 3020M and HP ProDesk 490 G1 Microtower
Both computers, the Dell OptiPlex 3020M and the HP ProDesk 490 G1 Microtower, were released during the same year - 2013.
If you are looking for the smaller form factor the Dell OptiPlex 3020M is the right one for you. It is smaller than the HP ProDesk 490 G1 Microtower and will fit more easily under your desk.
Processor
The two models have the same generation of Intel processors. We think that the 4 generation of Intel Processors have enough power to execute all of the home and office tasks that most people will care to do.
Memory
The HP ProDesk 490 G1 Microtower has 4 RAM slots while the Dell OptiPlex 3020M has only 2 slot(s). This is not something to worry about. Just make sure you take it into consideration when planning how much RAM you are going to use.
None of the desktops has an advantage when it comes to the speed of the RAM being used. Both models support RAM speeds of up to 1600. Additionally, if you will be needing a lot of RAM, better go for the HP ProDesk 490 G1 Microtower as it has the ability to run 32 GB of RAM. The Dell OptiPlex 3020M can do a bit less at max 16 GB. Most of the times, this should be sufficient for the majority of users.
Ports
In total the HP ProDesk 490 G1 Microtower has 10 USB ports. The Dell OptiPlex 3020M is inferior in this regard and packs 6 USB ports. In any case, if you miss USB ports, you can always purchase a USB hub. None of the desktop models has a USB 3.1 port (10Gb/s), so if you need a fast connection to your peripherals, like external Solid State Drive, you will need to look elsewhere.
Unfortunately, only the Dell OptiPlex 3020M has a DisplayPort. The HP ProDesk 490 G1 Microtower does not have one? Don't worry though, nowadays video adapters are cheap and you can get almost any combination of conversion types.
None of the models has an HDMI port. If your monitor supports only the HDMI interface, you will need to buy an adapter. Such adapters are cheap so nothing to worry about.
SATA ports are placed on the system board and it is where you connect your HDD, SSD and Optical Disk Drives. More SATA slots will allow you to have more drives running at the same time. In this regard the HP ProDesk 490 G1 Microtower is better equipped as it comes with 4 SATA slot(s), while the Dell OptiPlex 3020M has 1 slot(s).
M.2 SSD interface allows you to transfer data with higher speeds compared to the old SATA interface. Unfortunately, neither the Dell OptiPlex 3020M, nor the HP ProDesk 490 G1 Microtower has one. However, you can still use a SATA SSD drive which should give you satisfactory performance.
Make sure that the available M.2 slot supports the PCIe (also called NVMe) interface. This is important as there are M.2 slots which support only the inferior SATA III interface. For comparison, the SATA III interface has max speeds of 6Gb/s, while the PCIe 3.0 x4 will support speeds up to 32Gb/s!
Power Supply
Having a Power Supply Unit with high power rating is important, if you are going to use components which require extra power. The Dell OptiPlex 3020M comes with a decent 65 Watt PSU, but the HP ProDesk 490 G1 Microtower has a more powerful one rated at 300 Watts. Choosing either one depends on your specific requirements and use case. Also don't forget that some models might have more than one PSU option - try to always get the most powerful one, especially if you plan to upgrade to a powerful GPU.
Motherboard
