Alienware X51 R3 vs. HP ProDesk 600 G1 SFF
Comparison and Differences
Differences between Alienware X51 R3 and HP ProDesk 600 G1 SFF
If you are looking for a more modern desktop, then you should go with the Alienware X51 R3 which was released in 2015. The HP ProDesk 600 G1 SFF is older and entered production in 2013.
Both models have the same form factor, meaning reoughtly they have the same phiysical size and form.
Processor
Usually the newer the generation of the CPU, the better the performance and efficiency is. If your budget allows it, you should go with the Alienware X51 R3 as it is running a newer generation CPU. This is not to say that HP ProDesk 600 G1 SFF is bad - it can still run some powerful CPUs, albeit being an older generation.
Memory
The HP ProDesk 600 G1 SFF has 4 RAM slots while the Alienware X51 R3 has only 2 slot(s). This is not something to worry about. Just make sure you take it into consideration when planning how much RAM you are going to use.
The Alienware X51 R3 is using the faster 2133 MT/s RAM. The HP ProDesk 600 G1 SFF is slower by supporting RAM speeds of up to 1600 MT/s. In addition, you will be able to install the same amount of RAM in both models, and most probably 32 GB of RAM will be enough for most people. However, if you will be needing more RAM, make sure to check other desktop models too.
Ports
In total the HP ProDesk 600 G1 SFF has 10 USB ports. The Alienware X51 R3 is inferior in this regard and packs 8 USB ports. In any case, if you miss USB ports, you can always purchase a USB hub. What is nice about the Alienware X51 R3, is that it has 2 USB 3.1 port(s) which allows transfer of up to 10Gb/s. Unfortunately, the HP ProDesk 600 G1 SFF has no such port, thus restricting your transfer speeds significantly. For people who want to use external drives on regular basis, this might be an issue.
DisplayPort is crucial for any desktop machine. It is good to see that both models are featuring DisplayPorts. However, the HP ProDesk 600 G1 SFF comes with 2 ports, while the Alienware X51 R3 has only 1. If you are planning to use multiple monitors, the HP ProDesk 600 G1 SFF is the better choice.
None of the models has an HDMI port. If your monitor supports only the HDMI interface, you will need to buy an adapter. Such adapters are cheap so nothing to worry about.
SATA ports are placed on the system board and it is where you connect your HDD, SSD and Optical Disk Drives. More SATA slots will allow you to have more drives running at the same time. In this regard the HP ProDesk 600 G1 SFF is better equipped as it comes with 4 SATA slot(s), while the Alienware X51 R3 has 3 slot(s).
M.2 SSD interface allows you to transfer data with higher speeds compared to the old SATA interface. Unfortunately, neither the Alienware X51 R3, nor the HP ProDesk 600 G1 SFF has one. However, you can still use a SATA SSD drive which should give you satisfactory performance.
Make sure that the available M.2 slot supports the PCIe (also called NVMe) interface. This is important as there are M.2 slots which support only the inferior SATA III interface. For comparison, the SATA III interface has max speeds of 6Gb/s, while the PCIe 3.0 x4 will support speeds up to 32Gb/s!
Power Supply
Having a Power Supply Unit with high power rating is important, if you are going to use components which require extra power. The HP ProDesk 600 G1 SFF comes with a decent 240 Watt PSU, but the Alienware X51 R3 has a more powerful one rated at 330 Watts. Choosing either one depends on your specific requirements and use case. Also don't forget that some models might have more than one PSU option - try to always get the most powerful one, especially if you plan to upgrade to a powerful GPU.
Motherboard
