Dell OptiPlex 3010 SFF vs. HP ProDesk 600 G2 Mini
Comparison and Differences
Differences between Dell OptiPlex 3010 SFF and HP ProDesk 600 G2 Mini
If you are looking for a more modern desktop, then you should go with the HP ProDesk 600 G2 Mini which was released in 2016. The Dell OptiPlex 3010 SFF is older and entered production in 2012.
If you are looking for the smaller form factor the HP ProDesk 600 G2 Mini is the right one for you. It is smaller than the Dell OptiPlex 3010 SFF and will fit more easily under your desk.
Processor
Usually the newer the generation of the CPU, the better the performance and efficiency is. If your budget allows it, you should go with the HP ProDesk 600 G2 Mini as it is running a newer generation CPU. This is not to say that Dell OptiPlex 3010 SFF is bad - it can still run some powerful CPUs, albeit being an older generation.
Memory
Both models have have equal amount of ram slots (2 RAM). Usually two RAM slots are more than enough for most cases. However, the count should be taken into account when planning how much and what combination of RAM you are going to need for your system.
The HP ProDesk 600 G2 Mini is using the faster 2133 MT/s RAM. The Dell OptiPlex 3010 SFF is slower by supporting RAM speeds of up to 1600 MT/s. Additionally, if you will be needing a lot of RAM, better go for the HP ProDesk 600 G2 Mini as it has the ability to run 32 GB of RAM. The Dell OptiPlex 3010 SFF can do a bit less at max 8 GB. Most of the times, this should be sufficient for the majority of users.
Ports
In total the Dell OptiPlex 3010 SFF has 8 USB ports. The HP ProDesk 600 G2 Mini is inferior in this regard and packs 7 USB ports. In any case, if you miss USB ports, you can always purchase a USB hub. None of the desktop models has a USB 3.1 port (10Gb/s), so if you need a fast connection to your peripherals, like external Solid State Drive, you will need to look elsewhere.
Unfortunately, only the HP ProDesk 600 G2 Mini has a DisplayPort. The Dell OptiPlex 3010 SFF does not have one? Don't worry though, nowadays video adapters are cheap and you can get almost any combination of conversion types.
The Dell OptiPlex 3010 SFF comes with an HDMI port, while the HP ProDesk 600 G2 Mini does not support the interface. Of course missing HDMI port is something that can be easily fixed with a good adapter (e.g. DisplayPort to HDMI).
SATA ports are placed on the system board and it is where you connect your HDD, SSD and Optical Disk Drives. More SATA slots will allow you to have more drives running at the same time. In this regard the Dell OptiPlex 3010 SFF is better equipped as it comes with 2 SATA slot(s), while the HP ProDesk 600 G2 Mini has 1 slot(s).
If you want the fastest transfer speeds for your SSD, an M.2 interface is crucial. Thus, if the M.2 SSD slot is a mandatory requirement for you, go with the HP ProDesk 600 G2 Mini. Sadly, the Dell OptiPlex 3010 SFF has no such slot, and you will be forced to use the SATA interface instead.
Make sure that the available M.2 slot supports the PCIe (also called NVMe) interface. This is important as there are M.2 slots which support only the inferior SATA III interface. For comparison, the SATA III interface has max speeds of 6Gb/s, while the PCIe 3.0 x4 will support speeds up to 32Gb/s!
Power Supply
Having a Power Supply Unit with high power rating is important, if you are going to use components which require extra power. The HP ProDesk 600 G2 Mini comes with a decent 65 Watt PSU, but the Dell OptiPlex 3010 SFF has a more powerful one rated at 240 Watts. Choosing either one depends on your specific requirements and use case. Also don't forget that some models might have more than one PSU option - try to always get the most powerful one, especially if you plan to upgrade to a powerful GPU.
Motherboard
