HP ProDesk 600 G3 Microtower vs. HP ProDesk 600 G5 SFF
Comparison and Differences
Differences between HP ProDesk 600 G3 Microtower and HP ProDesk 600 G5 SFF
If you are looking for a more modern desktop, then you should go with the HP ProDesk 600 G5 SFF which was released in 2018. The HP ProDesk 600 G3 Microtower is older and entered production in 2017.
If you are looking for the smaller form factor the HP ProDesk 600 G5 SFF is the right one for you. It is smaller than the HP ProDesk 600 G3 Microtower and will fit more easily under your desk.
Processor
Usually the newer the generation of the CPU, the better the performance and efficiency is. If your budget allows it, you should go with the HP ProDesk 600 G5 SFF as it is running a newer generation CPU. This is not to say that HP ProDesk 600 G3 Microtower is bad - it can still run some powerful CPUs, albeit being an older generation.
Memory
Both models have have equal amount of ram slots (4 RAM). Usually two RAM slots are more than enough for most cases. However, the count should be taken into account when planning how much and what combination of RAM you are going to need for your system.
The HP ProDesk 600 G5 SFF is using the faster 2666 MT/s RAM. The HP ProDesk 600 G3 Microtower is slower by supporting RAM speeds of up to 2400 MT/s. Additionally, if you will be needing a lot of RAM, better go for the HP ProDesk 600 G5 SFF as it has the ability to run 128 GB of RAM. The HP ProDesk 600 G3 Microtower can do a bit less at max 64 GB. Most of the times, this should be sufficient for the majority of users.
Ports
Both models have the same amount of USB ports for total count of 11. If this is not enough, using a USB hub is always a viable option. What is nice about the HP ProDesk 600 G5 SFF, is that it has 5 USB 3.1 port(s) which allows transfer of up to 10Gb/s. Unfortunately, the HP ProDesk 600 G3 Microtower has no such port, thus restricting your transfer speeds significantly. For people who want to use external drives on regular basis, this might be an issue.
The DisplayPort is usually the more popular video port used with desktops and laptops, while the HDMI is used predominantly in consumer electronics. That's why, it is good to see that both of the models come with a DisplayPort.
None of the models has an HDMI port. If your monitor supports only the HDMI interface, you will need to buy an adapter. Such adapters are cheap so nothing to worry about.
SATA ports are placed on the system board and it is where you connect your HDD, SSD and Optical Disk Drives. More SATA slots will allow you to have more drives running at the same time. In this regard the HP ProDesk 600 G3 Microtower is better equipped as it comes with 5 SATA slot(s), while the HP ProDesk 600 G5 SFF has 3 slot(s).
When your goal is to have the fastest SSD transfer speeds, an M.2 interface is crucial. Thus, it is good that both models have M.2 SSD slots. Today M.2 SSDs are not much more expensive than the average SATA drives, so it really does not make sense to invest in SATA drives anymore.
Make sure that the available M.2 slot supports the PCIe (also called NVMe) interface. This is important as there are M.2 slots which support only the inferior SATA III interface. For comparison, the SATA III interface has max speeds of 6Gb/s, while the PCIe 3.0 x4 will support speeds up to 32Gb/s!
Power Supply
Having a Power Supply Unit with high power rating is important, if you are going to use components which require extra power. The HP ProDesk 600 G5 SFF comes with a decent 180 Watt PSU, but the HP ProDesk 600 G3 Microtower has a more powerful one rated at 250 Watts. Choosing either one depends on your specific requirements and use case. Also don't forget that some models might have more than one PSU option - try to always get the most powerful one, especially if you plan to upgrade to a powerful GPU.
Motherboard
