Dell OptiPlex 9020 USFF vs. HP ProDesk 600 G3 SFF
Comparison and Differences
Differences between Dell OptiPlex 9020 USFF and HP ProDesk 600 G3 SFF
If you are looking for a more modern desktop, then you should go with the HP ProDesk 600 G3 SFF which was released in 2017. The Dell OptiPlex 9020 USFF is older and entered production in 2013.
If you are looking for the smaller form factor the Dell OptiPlex 9020 USFF is the right one for you. It is smaller than the HP ProDesk 600 G3 SFF and will fit more easily under your desk.
Processor
Usually the newer the generation of the CPU, the better the performance and efficiency is. If your budget allows it, you should go with the HP ProDesk 600 G3 SFF as it is running a newer generation CPU. This is not to say that Dell OptiPlex 9020 USFF is bad - it can still run some powerful CPUs, albeit being an older generation.
Memory
The HP ProDesk 600 G3 SFF has 4 RAM slots while the Dell OptiPlex 9020 USFF has only 2 slot(s). This is not something to worry about. Just make sure you take it into consideration when planning how much RAM you are going to use.
The HP ProDesk 600 G3 SFF is using the faster 2400 MT/s RAM. The Dell OptiPlex 9020 USFF is slower by supporting RAM speeds of up to 1600 MT/s. Additionally, if you will be needing a lot of RAM, better go for the HP ProDesk 600 G3 SFF as it has the ability to run 64 GB of RAM. The Dell OptiPlex 9020 USFF can do a bit less at max 16 GB. Most of the times, this should be sufficient for the majority of users.
Ports
In total the HP ProDesk 600 G3 SFF has 11 USB ports. The Dell OptiPlex 9020 USFF is inferior in this regard and packs 6 USB ports. In any case, if you miss USB ports, you can always purchase a USB hub. None of the desktop models has a USB 3.1 port (10Gb/s), so if you need a fast connection to your peripherals, like external Solid State Drive, you will need to look elsewhere.
The DisplayPort is usually the more popular video port used with desktops and laptops, while the HDMI is used predominantly in consumer electronics. That's why, it is good to see that both of the models come with a DisplayPort.
None of the models has an HDMI port. If your monitor supports only the HDMI interface, you will need to buy an adapter. Such adapters are cheap so nothing to worry about.
SATA slots are located on the motherboard and it is where SSD, HDD and Optical Disk Drives are connected. Each of the two models being compared have 2 SATA slot(s). Keep in mind that having too few SATA slots might limit your options for connecting additional memory drives.
When your goal is to have the fastest SSD transfer speeds, an M.2 interface is crucial. Thus, it is good that both models have M.2 SSD slots. Today M.2 SSDs are not much more expensive than the average SATA drives, so it really does not make sense to invest in SATA drives anymore.
Make sure that the available M.2 slot supports the PCIe (also called NVMe) interface. This is important as there are M.2 slots which support only the inferior SATA III interface. For comparison, the SATA III interface has max speeds of 6Gb/s, while the PCIe 3.0 x4 will support speeds up to 32Gb/s!
Power Supply
Having a Power Supply Unit with high power rating is important, if you are going to use components which require extra power. The HP ProDesk 600 G3 SFF comes with a decent 180 Watt PSU, but the Dell OptiPlex 9020 USFF has a more powerful one rated at 200 Watts. Choosing either one depends on your specific requirements and use case. Also don't forget that some models might have more than one PSU option - try to always get the most powerful one, especially if you plan to upgrade to a powerful GPU.
Motherboard
